landscape with bow

Build your own bow shooting stand

It’s almost time for deer season, so you’ve been shooting your bow every chance you get… right?  You are probably tired of laying your high-priced bow on the ground when you retrieve your arrows.  Perhaps you dislike leaning over to pick up your next arrow after every shot.  Or maybe you are just bored (like me) and decide you want to be MacGyver with some leftover junk in your garage. Regardless, if you are looking for a way to protect your bow, your back, and your arrows, building your own bow stand is a lot easier than you may think. Here’s a cheap and easy way to build your own bow shooting stand.

Step 1: Build Your Own Bow Shooting Stand - Gather Materials

In order to keep costs low, I elected to use some old pipe and fittings I had laying around the house.  While you could potentially do with other sizes, I used primarily 1-1/2″ SCHD40 PVC with good results. Here’s what I used:

  • ~9 feet of 1-1/2″ PVC pipe
  • Four 1-1/2″ Tees
  • Two 1-1/2″ Elbows
  • Two 1-1/2″ Caps
  • Two 1-1/2″ to 3/4″ Reducers
  • Two 3/4″ Elbows
  • 8″ to 12″ of 3/4″ PVC pipe
  • Rubber foam pipe insulation (to fit the 3/4″ PVC)
  • PVC Primer/Glue
Keep in mind, if you have a lot of a different size pipe laying around you still may be able to build this with some substituting. However, you may want to let your buddy use it first, just in case.

Step 2: Make the Cut

Cut a 48″ section of 1-1/2″ pipe.  This will be the vertical portion of the stand. Now cut six, 8″ sections of the remaining pipe.  These will form the base of the stand. Next cut the remaining 1-1/2″ PVC pipe evenly down the center (leaving roughly four to six inches for each). The actual length of these pieces is not critical, as they simply form the arrow holders later on. 

Cut the 3/4″ pipe in half, leaving each piece approximately six inches long. The actual length of these pieces are not critical, provided they are at least 1-1/2″ wider than your bow limbs. 

Step 3: To Glue or Not to Glue

Most of this next step is up to personal preference.  I chose not to glue the majority of my stand so that I could disassemble when not in use to save space.  However, at a minimum you must glue the three Tees in the base together for the stand to work.  The rest of the items can be press-fit or glued to make it as permanent as you would like. 

The foam on the 3/4″ pipe is an added touch that may not be necessary.  However, if you baby your bow around the house like I do you’ll like the added protection and extra hold it gives when shooting from unlevel ground. 

Want some extra credit? Swap the Tee on top for a 4-way Tee and attach a 1-1/2″ to 3″ reducer coupling with some of your excess 1-1/2″ pipe.  It holds a typical “beverage” can quite nicely. Modify as necessary to make your bow shooting stand your way!  If you have any questions, feel free to submit a question on our online contact form (HERE).

Share this post

Share on facebook
Share on twitter
Share on email

Leave a Comment

Your email address will not be published. Required fields are marked *

additional articles

other recent blog posts

Rich Peace

Run-N-Gun Camera Setup

Entering the 2019 deer season, I was confident I had found the perfect run-n-gun camera setup. I decided to use the Fourth Arrow Run-n-Gun base

Read More »
Rich Peace

Fourth Arrow Final Rest

The all new Final Rest by Fourth Arrow is a highly configurable shooting rest system designed to meet the needs of a wide variety of

Read More »